Litter-Robot 5 LitterHopper Disconnected or Not Dispensing? Fixes for LR5 & 5 Pro

Last updated: October 25, 2026

The LitterHopper is the automatic litter-refill accessory for the Litter-Robot 5 and 5 Pro – it holds about 17 cups of litter and tops up the globe on its own. When it works, you rarely think about it. When it shows “Hopper Disconnected,” stops dispensing, or jams, it gets confusing fast – partly because a hopper that is not dispensing is often behaving normally.

This guide covers the Litter-Robot 5 and 5 Pro with the LitterHopper accessory only. It does not apply to the Litter-Robot 3 or 4, which use a different hopper design and different procedures. Every step below comes from Whisker’s current official documentation.

First: How the LitterHopper Decides to Dispense

Before troubleshooting, understand the normal behavior – most “not dispensing” complaints turn out to be this:

  • The Litter-Robot 5 measures the litter bed height with sensors in the bezel at the end of each clean cycle.
  • If the level is below the optimal range (the MAX fill line inside the globe), the LitterHopper dispenses during the NEXT clean cycle – not immediately. The globe briefly pauses rotation while dispensing.
  • Dispensing happens ONLY when needed and ONLY during a clean cycle. A full cycle must complete before dispensing occurs on the following cycle.
  • Each dispense runs up to 20 seconds. If the litter is very low, it can take several cycles to return to the optimal level.
  • An uneven litter bed (higher on the sides, lower in the center) can prevent the unit from detecting a low level correctly.
  • Whisker recommends clay-clumping litter. Translucent or white crystal litter may affect litter-level and drawer-full accuracy.

So: if the globe’s litter level is already near the MAX line, the hopper correctly does nothing. That is not a fault.

Which Problem Do You Have?

  • “Hopper Disconnected” message (LCD screen, app notification, or the hopper card missing from the app) – go to Fix 1.
  • Hopper is connected but never dispenses – go to Fix 2. But first re-read the section above – if the litter level is already at the MAX line, nothing is wrong.
  • “Hopper jammed” message, or litter visibly stuck – go to Fix 3.
  • Hopper looks fine but the globe’s litter level keeps dropping – go to Fix 2, then the test cycles.
  • No hopper fault at all – the robot itself will not cycle or shows other errors – this guide is not the problem; see Litter-Robot not cycling guide.

Decision gate: before any disassembly

Do not remove the bonnet, globe, or hopper for deeper access until you have passed this gate. It is built from three documented elements: the control-panel motor test, the clear-error shortcut, and Whisker’s stop conditions.

Gate check (documented)If it passesIf it fails – next step
1. Manual motor test: press and hold the Empty and Connect buttons together for 3 seconds.A small amount of litter dispenses – the motor is working properly. Do not disassemble to chase a motor fault.Litter does not dispense – that suggests an issue with the hopper or the unit. Stop here and contact Whisker Customer Experience; do not treat a failed test as an automatic replace-the-motor verdict.
2. Clear-error shortcut (only if the LCD shows “Hopper Disconnected”): short-press Cancel to clear the message, then press and hold Cycle and Empty together for 3 seconds (the LCD screen will stay black), then short-press Cycle to run a Clean Cycle and confirm the message has cleared.The message has cleared – continue with the normal fix for your symptom, not with disassembly.The message returns – continue to Fix 1 (reinstall) and Fix 3 checkpoints, in order.
3. Stop conditions – stop and contact Whisker Customer Experience if any of these apply:None apply – you may proceed to the fix for your symptom.The hopper still is not detected after the full reinstall procedure; the manual motor test fails; the metal prong looks damaged; jam or disconnected errors keep returning after clearing; your firmware is not current and no update option is available; or you have worked through the official steps without success. Do not open sealed electronics or bypass safety mechanisms.

Fix 1: Hopper Disconnected

Before you begin (Whisker’s checklist): the unit is plugged in; the unit is connected to Wi-Fi and online; the firmware is on the most current version. If your firmware is not current, contact Whisker Customer Experience for assistance.

How you will know: a push notification that the LitterHopper is disconnected, a “LitterHopper disconnected” status in Device Activity, or the LitterHopper card disappearing from the Device Status page in the app.

Step 1 – Check the installation. Lift the LitterHopper up and away from the unit. (If it contains litter, hold a container underneath to catch spills.) Check that there is no gap between the bonnet and the base, and that the bonnet hinge is fully seated in the base hinge pocket.

Step 2 – Check the connection and dispensing area. Debris here can prevent detection. Inspect and clear litter, clumps, or debris from: the dispensing area and the metal prong on the underside of the LitterHopper – the prong must be visible, clean, and not damaged; and the dispensing area on the base, including the circular pockets. If you can see debris in the circular pockets, remove the bonnet for easier access and vacuum the pockets so the hopper’s posts can make full contact. Whisker recommends inspecting and vacuuming these areas regularly to prevent errors from returning.

Step 3 – Reinstall the LitterHopper. If you removed the bonnet, reinstall it by aligning it with the hinge at the back of the base and rotating it downward until fully seated and latched. Align the hopper’s posts with the circular pockets and lower it into place. Make sure there is no gap between the bottom of the hopper and the base, and that the mounting tab is fully seated in the slot on the bonnet. When fully installed, there should be no gaps around the top, bottom, or sides – the LCD screen will display a “LitterHopper detected” message, and the app will confirm with a push notification, “Hopper detected” / “Hopper enabled” in History, and a LitterHopper card on the Status page. Then press the Cancel button to zero the weight scale.

What success looks like: the “LitterHopper detected” message on the LCD and the hopper card back in the app. If it fails: the unit still does not detect the hopper and it does not appear in the app – re-check the seating and repeat the installation steps.

Shortcut from Whisker’s control-panel documentation: if the LCD shows “Hopper Disconnected,” you can also short-press Cancel to clear the message, then press and hold Cycle and Empty together for 3 seconds (the LCD screen will stay black), then short-press Cycle to run a Clean Cycle and confirm the message has cleared.

Fix 2: Hopper Connected but Not Dispensing

Check the app first. Look for notifications like “LitterHopper low,” “LitterHopper jammed,” or “LitterHopper disconnected” – as push notifications, on the hopper status, or in Device Activity. They point at the cause, though you may still need the steps below.

Rule out the normal cases. The hopper will not dispense if: the litter level is already within the optimal range; the unit has an active error state; or the hopper is empty, jammed, or not properly installed. An empty hopper may try to dispense but have nothing to add.

Make sure the litter level is genuinely low. Add litter to the globe until it reaches the MAX fill line, then press Cancel to zero the weight scale, then press Cycle to run a Clean cycle (this sifts any excess into the waste drawer). Note: if the hopper was low and you refilled it, the low-litter message may not clear immediately – run two clean cycles so the unit can detect the updated level.

Clean the curtain sensors. Dust, fur, or debris on the curtain sensor can interfere with litter-level detection and stop the hopper from dispensing correctly. Gently wipe the curtain sensor cover with a clean, dry microfiber cloth. Do not use water, liquids, or cleaning wipes. Do not use a vacuum or compressed air. Avoid scratching the sensor surface. After cleaning, short-press Cancel to reset the weight sensors. Any time you affect the weight or placement of the unit – emptying the drawer, adding or removing litter, cleaning or moving it – press Cancel so the weight sensors detect your cat and cycle properly.

Calibrate the optimal litter level. This teaches the unit what “full” looks like. First confirm in the Whisker app that your Litter-Robot 5 is on firmware version 5.09.06 or above (if not, contact Whisker Customer Experience). Then press and hold the Cancel and Empty buttons together for 3 seconds – the robot will run a Clean Cycle and calibrate the optimal litter bed level.

Fix 3: Hopper Jammed – checkpoint list

Work through these checkpoints in order. At each checkpoint, observe first, then take only the documented action for that checkpoint. Safety warnings are preserved: do not disassemble anything beyond this official consumer procedure, and never force sealed components.

Checkpoint – what to observeDocumented action
Checkpoint 1 – Motor area near the flexible flaps: is a foreign object stuck in the flap area?If a foreign object is stuck there, remove it with a small tool such as tweezers, taking care not to damage or bend the flaps.
Checkpoint 2 – Dispensing opening at the bottom of the LitterHopper: are clumps or buildup blocking litter flow?Remove any clumps or buildup blocking litter flow.
Checkpoint 3 – Dispensing area inside the globe key: are clumps or debris blocking litter?Remove any clumps or debris that may be blocking litter flow. Make sure all areas are clear before continuing.
Checkpoint 4 – Deeper access (only if the checkpoints above did not clear the jam, and only after the decision gate above): is the unit in the Home/Ready position? Are the circular pockets, base hinge pocket, and base clear?Make sure the unit is in the Home/Ready position. Remove the bonnet by pressing and holding the latches on both sides and rotating it to about 45 degrees before pulling up and away (it cannot be removed in its fully open position). Remove any bezel accessories such as the fence. While holding the globe key in place, lift the globe by the black handle and remove it from the base. Vacuum dust, loose litter, or clumps from the circular pockets, the base hinge pocket, and the base.
Checkpoint 5 – Globe key and base pockets: is the globe key free of litter and debris, and seated correctly?Making sure the globe key is free of litter and debris, place it into the rear of the globe with the rectangular opening facing up, then – while holding the key in place – set the globe back into the base so the key drops fully into its pocket.
Checkpoint 6 – Reassembly: is the bonnet hinge fully seated, with no gap, and does the key protrude correctly?Rotate the bonnet upward at a 45 degree angle, align the hinge at the back of the base, rotate downward over the globe and push down from the top until latched – the key must protrude through the opening in the back of the bonnet. Confirm the bonnet hinge sits completely inside the base hinge pocket with no gap between bonnet and base. Then reinstall the hopper as in Fix 1 and fill it to the MAX fill line.

Do not disassemble anything beyond this official consumer procedure, and never force sealed components.

Test Whether It Is Fixed: Run Test Cycles

  1. Remove litter from the globe until the level is significantly below the MAX fill line. (The auto-dispense will NOT activate unless the globe’s litter level is low.)
  2. Short-press Cancel, then short-press Cycle to run the first cycle. The unit will detect the low litter level and save it to memory.
  3. Once the unit is back at the home position, press Cycle again to run another cycle.

What success looks like: the LitterHopper automatically dispenses litter during the test cycle. If it fails: the hopper still does not dispense, or the panel/app shows “LitterHopper jammed” – continue to the motor test below.

Manual Motor Test

To check the hopper motor itself: press and hold the Empty and Connect buttons together for 3 seconds. A small amount of litter should dispense.

What success looks like: litter dispenses – the motor is working properly. If it fails: litter does not dispense. That suggests an issue with the hopper or the unit – contact Whisker Customer Experience. Do not treat a failed test as an automatic “replace the motor” verdict; support needs to diagnose it.

Can the LR5 Run Without the LitterHopper?

Yes. You can disable the LitterHopper from the control panel by pressing and holding Cycle and Empty together for 3 seconds (the LCD confirms), or in the Whisker app under Controls – LitterHopper. The Litter-Robot 5 then works as a regular Litter-Robot 5 – you just refill litter by hand. Re-enable it the same way whenever you want it back.

When to Stop and Contact Whisker Support

Stop troubleshooting and contact Whisker Customer Experience if: the hopper still is not detected after the full reinstall procedure; the manual motor test fails; the metal prong looks damaged; jam or disconnected errors keep returning after clearing; your firmware is not current and no update option is available; or you have worked through the official steps above without success. Do not open sealed electronics or bypass safety mechanisms.

Reset Terminology – Do Not Mix These Up

Whisker’s hopper procedures use several distinct actions. They are not all “a reset”: clearing an error message (short-press Cancel) – reconnecting the hopper (physical reinstall) – zeroing the weight sensors (short-press Cancel after adding litter or moving the unit) – calibrating the litter level (hold Cancel + Empty for 3 seconds) – testing the motor (hold Empty + Connect for 3 seconds) – power cycling the robot. If you need the general LR5 reset procedures, see how to reset a Litter-Robot.

Sources

Manufacturer documentation is the primary source for this guide. Any practical sequencing or emphasis beyond Whisker’s stated steps is editorial judgment, not manufacturer instruction.

Editorial responsibility: Mohammed Algaari – Founder & Editor